Welcome to the VanDyke Software Forums

Join the discussion today!


Go Back   VanDyke Software Forums > Scripting

Reply
 
Thread Tools Rate Thread Display Modes
  #1  
Old 02-10-2019, 07:08 AM
stamati76 stamati76 is offline
Registered User
 
Join Date: Nov 2018
Posts: 1
Script to Backup running config to local PC

I have very little experience with scripting and i was wondering if anyone could help me run a script that pulled the running configuration from all my devices in session manager?

I have run the following script that hangs on line 25. Basically, it's looking for the devices file, which i have not yet written

How could i change it to look through my session manager or export all the devices from session manager to a readable file for the vbs script to read?

Code:
#$language = "VBScript"
#$interface = "1.0"

' Test Script to log in via SSH/telnet and enters in privileged mode
' IF enable password is not set or you connect with TACACS/Radius directly in privileged mode, 
' then comment the lines after Loop until the next comment section
' This version uses only one "devices.txt" file to store IP Address;hostname;username;password;enable password

Dim g_objTab
Set g_objTab = crt.GetScriptTab

Sub Main
	CRT.Screen.synchronous = True
	If crt.Session.Logging Then 								' Turn off session logging before setting up our script's
	   crt.Session.Log False									' logging... if needed
	End If
		Dim fso													' Declaring filesystemobject
		Dim fil													' Declaring file containing devices
		Dim vWaitFors											' Array to determine if RSA key is known, also to determine if SSH or Telnet is enabled
		vWaitFors = Array("(yes/no)?",_
							"port 22: Connection refused",_
							"assword:")
		Const DEVICE_FILE_PATH = ".\devices.txt"				' Path to devices list (can be modified, now it points to same folder where script is located)
		Set fso = CreateObject("Scripting.FileSystemObject")
		Set fil = fso.OpenTextFile(DEVICE_FILE_PATH)			' Open devices file
	While Not fil.AtEndOfStream									' Read devices.txt. Until not EOF do :
		line = fil.ReadLine										' Read line by line
		Device = Split(line, ";")(0)							' Device's IP address
		hostname = Split(line,";")(1)							' hostname - for easy human read
		username = Split(line,";")(2)							' username to connect to device
		pass = Split(line,";")(3)								' password for username
		pass2 = Split(line,";")(4)								' password to enter privileged mode if needed
		crt.Screen.Send "ssh " + username + "@" + Device & chr(13)	' First try to connect via SSH to device
		Do
		Dim nResult	
		nResult = crt.Screen.WaitForStrings(vWaitFors)
		Select Case nResult										' Now determine if RSA key has to be added or not in SSH case or try via Telnet
			Case 1												' RSA key for /.ssh/known_hosts must be added
		crt.Screen.Send "yes" & chr(13)							' so send and "yes"
		crt.Screen.WaitForString "assword:"						' then wait for password prompt
		crt.Screen.Send pass & chr(13)							' and send pass
			Case 2												' SSH not enabled on device, then go for telnet
		crt.Screen.Send "telnet " + Device & chr(13)
		crt.Screen.WaitForString "sername:"
		crt.Screen.Send username & chr(13)
		crt.Screen.WaitForString "assword:"
		crt.Screen.Send pass & chr(13)
			Case 3												' RSA key already learned
		crt.Screen.Send pass & chr(13)							' just send pass from credentials file
		End Select
		Exit Do
		Loop
		crt.Screen.WaitForString ">"							' Waits for prompt
		crt.Screen.Send "enable" & chr(13)						' Enable
		crt.Screen.WaitForString "assword:"
		crt.Screen.Send pass2 & chr(13)							' sends enable pass
		crt.Screen.WaitForString "#"							' waits for privileged mode prompt
		' From now on, just put whatever commands you need for your device
		' use crt.Screen.Send "command" & chr(13) --- to send what you want, chr(13) stands for ENTER key
		' use after each command an crt.Screen.WaitForString "#" -- to wait for prompt after command's output
		' Or even better just use SendExpect "command", "prompt" --- see below function
		SendExpect "terminal length 0", hostname + "#"
		crt.Session.logFileName = ".\" + hostname + ".txt"
		crt.Session.Log True
		SendExpect "show running-config", hostname + "#"
		crt.Session.Log False
		' Commands sent/received output ends here. Next is disconnecting from device	
		SendExpect "exit", "]$ "								' Closes connection & Waits for Terminal Server prompt and is ready for next device
	Wend	
	fil.Close													' Close devices file
End Sub															' THE END OF THE UNIVERSE AS YOU KNEW IT:)
Function SendExpect(szSend, szExpect)							' Made this to replace the Screen.Send/Screen.WaitForString pairs
	' Returns true if the text in 'szSend' was successfully sent and
	' the text in 'szExpect' was successfully found as a result.
    ' If we're not connected, we can't possibly return true, or even send/recv text
    
	if g_objTab.Session.Connected <> True then exit function
        
    g_objTab.Screen.Send szSend & vbcr
    g_objTab.Screen.WaitForString szExpect

    SendExpect = True
End Function
Reply With Quote
  #2  
Old 02-10-2019, 06:08 PM
bgagnon bgagnon is offline
VanDyke Technical Support
 
Join Date: Oct 2008
Posts: 3,966
Hi stamati76,

Presently there's not an easy way to iterate over the sessions in Session Manager. I have added this thread to a feature request in our product enhancement database to add Sessions object to scripting API for iterating over all sessions in Session Manager. Should a future release of SecureCRT include this feature, notification will be posted here.

If you prefer direct email notification, send an email to support@vandyke.com and include "Feature Request - Forum Thread #13398" in the subject line or use this form from the support page of our website.

There may be a way you can export the connection data. Please contact us via email (support@vandyke.com) and reference "Attn Brenda - Forum Thread #13398" in the subject line.

In your email please let me know the version of SecureCRT and what OS you are running it on.
__________________
Thanks,
--Brenda

VanDyke Software
Technical Support
support@vandyke.com
(505) 332-5730
Reply With Quote
Reply

Tags
backup , scripting , session manager


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 02:34 AM.